Aug-Line Aug-Line Terminator Element 15A

This is a noise absorption and elimination module that uses plenty of "Aug alloy", which is a triple blend of gold, silver, and platinum in the conductor part.
The interior is made of special materials and fine ceramics with a noise-absorbing effect.
It is used by inserting it into the speaker cable or power cable that you are currently using.
It has been praised for increasing the transparency of the background and making the music as a whole more energetic.

It is a fusion of the latest noise absorbing elements and fine ceramics, and can be expected to be effective in all parts of the audio alternating current, including AC and signal.

1. How to use it on the speaker

The easiest way to use it is to connect a terminator element in series to the output side of your speaker cable.

In the case of a typical speaker, the use of four terminators (15A) can have a very large effect.

The confirmed effects include an increase in the signal-to-noise ratio and an increase in the amount of information, but in particular, the speed and resolution of the low frequencies have been greatly improved, and the feeling of staggering and wobbly is no longer felt.



For small full-range and bi-wire high-frequency units, the terminator (3A) can be used sufficiently.

If you use (3A) on the low frequency side of a large speaker system, it tends to have a slightly lighter sound quality, although it is effective.

Ideally, it is used in front of each unit, i.e. after it has passed through the network, and it has an incredible effect.

In that case, I think it is better to use (15A) for the low frequency range and (3A) for the mid and high range.

In addition, the point discovered during various experiments is that when used at the outlet of the parallel resistance (R2 resistor) of the damping resistor in the mid and high frequencies, the sound field was nearly doubled in one fell swoop.

2. How to use it in a signal system

As for how to use it in a signal system, it is basically just a matter of putting it in series with the circuit.

If you use the terminator to hot-cold your current signal cable, you can see amazing results.

I think it is a good idea to use it for balanced signal circuits in balanced circuits.

I don't think there is a need for a ground wire for the balance circuit.

All elements used are terminator (3A) and there is no problem.

If you are making your own machine or can repair it, you can expect a great effect by connecting it in series between the connector and the circuit of the device.

We were able to confirm a significant effect on all digital signals.

3. How to use it in the power supply system

As for how to use it in the power supply system, it is only used in series with the circuit, but in the case of a power supply, please be careful to observe the allowable current.

The terminator (15A) is 220V15A and the terminator (3A) is 220v3A.

If it is used more than that, it may cause heat generation or fire, so please use it within the standard.

The primary and secondary sides of the power supply are effective as a place of use, and I think it is effective if you use it in a power strip as a simple use.

As an unusual way of use, it has a surprising effect when used between a diode and a smoothing capacitor after rectification.

During the experiment, I discovered that the presence of a transformer with good sound and a diode with good sound means that transformer noise and diode noise are generated.

Regarding the power supply, it is very dangerous if you are unfamiliar with it, so we recommend that you ask a qualified person.

As is common to this Terminator series, the purity of the sound is increased by removing the noise generated by alternating current and the high-frequency noise generated on the circuit, the transparency and resolution of the background are increased, and the grain of the sound becomes clearer. Stringed instruments and vocals are now realistically represented.
We consulted with Mr. Muto of Aug-Line and had the jumper cable made (^^)/ by processing the terminator The Aug-Line terminator is a magical item that makes the sound smoother even though the S/N is greatly increased and the resolution and number of sounds increase. It has already been installed in SP cables and power supply boxes. This time, the S/N has been very high since the beginning of the connection, and the resolution has been improved and the number of sounds has also increased. The sound has become smoother in a few hours, but it has become noticeable (^_^;) that the mid and high frequencies have improved and the low frequencies have not come out